MOUNTED BALL BEARING UNIT TYPES

Display information about:

Links on this page will open a .PDF product specification sheet.

PILLOW BLOCKS

The most extensively used bearing units. UCP, UCPK and SBP are fixed to the shafts with set screws in the inner ring. HCP and SAP are fixed to the shaft with eccentric locking collars. UPCK also has a low center height.

UCP Standard Duty Set Screw — View Page
HCP Standard Duty Eccentric Locking Collar — View Page
SBP Light Duty Set Screw — View Page
SAP Light Duty Eccentric Locking Collar — View Page
UCPK Low Center Height Set Screw — View Page

TAPPED BASE PILLOW BLOCKS

UCPA Standard Duty Set Screw units are compact pillow blocks for limited space applications. Mounting is done with threaded bolts into the base.

UCPA Standard Duty Set Screw — View Page

PRESSED STEEL PILLOW BLOCKS

SAPP and SBPP are lightweight units consisting of two pressed steel plates. Used with light loads at low to medium speed with SA or SB inserts.

SBPP Light Duty Set Screw — View Page
SAPP Light Duty Eccentric Locking Collar — View Page

4-BOLT SQUARE FLANGE UNITS

UCF and HCF standard duty, and SAF light duty units bolt to the sides of equipment with four bolts. Set screws and eccentric locking collars have the same mounting methods as housings with the "P" suffix.

UCF Standard Duty Set Screw — View Page
HCF Standard Duty Eccentric Locking Collar — View Page
SAF Light Duty Eccentric Locking Collar — View Page

2-BOLT FLANGE UNITS

Housing saves space and weight and is installed with two bolts. Types UCFL and HCFL are standard duty units, while SBFL is light duty.

UCFL Standard Duty Set Screw — View Page
HCFL Standard Duty Eccentric Locking Collar — View Page
SBFL Light Duty Set Screw — View Page

2-BOLT OVAL FLANGE UNITS - LF TYPE

SBLF and SALF light duty, 2-bolt flange units are used with SB inserts only.

SBLF Light Duty Set Screw — View Page
SALF Light Duty Eccentric Locking Collar — View Page

4-BOLT ROUND FLANGE UNITS

The 4-bolt UCFC standard duty unit with a set screw is installed where concentricity is required.

UCFC Standard Duty — View Page

3-BOLT FLANGE UNITS

Made from ductile iron, types SAFCT and SBFCT are light duty units used with SA and SB inserts only.

SBFCT/SAFCT Light Duty — View Page

FLANGE BRACKET UNITS

Designed for standard duty, UCFB has three set holes on only one side of the flange. It is used where mounting space is limited and the housing can be fixed on one side only.

UCFB Standard Duty — View Page

TAKE UP UNITS

UCT and UCST are standard duty units used where the center of the main shaft requires free alignment. UCT has a narrow slot; UCST has a wide slot.

UCT Standard Duty Set Screw - Narrow Slot — View Page
UCST Standard Duty Set Screw - Wide Slot — View Page

BEARING INSERTS

Radial ball bearings adapted to fit into a mounted housing. Types UC, HC and SER are standard duty; SA and SB are light duty. SER also has a snap ring and groove. "C" prefix indicates cylindrical OD. Units with "G" suffix are relubricatable.

UC Standard Duty Set Screw — View Page
HC Standard Duty Eccentric Locking Collar — View Page
SA Eccentric Locking Collar/CSA Cylindrical OD — View Page
SB Set Screw/SBG Relubricatable/CSB Cylindrical OD — View Page
SER Standard Duty - Cylindrical OD — View Page

TRI-PLY SEAL AG BEARINGS

Agricultural bearings with a triple lip seal and outer shroud that prevent lubrication loss and protect against moisture and abrasion. Relubricatable (GW200PPB) and non-relubricatable (W200PPB) types available, with round or square bores.

GW200PPB Triple Lip Seals - Relubricatable — View Page
W200PPB Triple Lip Seals - Non-relubricatable — View Page

DISK HARROW UNITS BEARINGS

209 and 211 series units feature two heavy gauge pressed steel plates riveted to form a housing, fitted with two rubber O-rings surrounding a triple lip sealed bearing. Use with square or round bores. Units can be relubricated.

209 and 211 Series Disk Harrow — View Page